Long-Term Ultrasound Twinkling Detectability and Safety of a Polymethyl Methacrylate Soft Tissue Marker Compared to Conventional Breast Biopsy Markers-A Preclinical Study in a Porcine Model.

OBJECTIVE: We have studied the use of polymethyl methacrylate (PMMA) as an alternative biopsy marker that is readily detectable with ultrasound Doppler twinkling in cases of in vitro, ex vivo, or limited duration in vivo settings. This study investigates the long-term safety and ultrasound Doppler twinkling detectability of a PMMA breast biopsy marker following local perturbations and different dwell times in a 6-mo animal experiment. METHODS: This study, which was approved by our Institutional Animal Care and Use Committee, involved three pigs and utilized various markers, including PMMA (Zimmer Biomet), 3D-printed, and Tumark Q markers. Markers were implanted at different times for each pig. Mesh material or ethanol was used to induce a local inflammatory reaction near certain markers. A semiquantitative twinkling score assessed twinkling for actionable localization during monthly ultrasounds. At the primary endpoint, ultrasound-guided localization of lymph nodes with detectable markers was performed. Following surgical resection of the localized nodes, histomorphometric analysis was conducted to evaluate for tissue ingrowth and the formation of a tissue rind around the markers. RESULTS: No adverse events occurred. Twinkling scores of all markers for all three pigs decreased gradually over time. The Q marker exhibited the highest mean twinkling score followed by the PMMA marker, PMMA with mesh, and Q with ethanol. The 3D-printed marker with mesh and PMMA with ethanol had the lowest scores. All wire-localized lymph nodes were successfully resected. Despite varying percentages of tissue rind around the markers and a significant reduction in overall twinkling (p < 0.001) over time, mean PMMA twinkling scores remained clinically actionable at 6 and 5 mo using a General Electric C1-6 probe and 9L-probe, respectively. CONCLUSIONS: In this porcine model, the PMMA marker demonstrates an acceptable safety profile. Clinically actionable twinkling aids PMMA marker detection even after 6 mo of dwell time in porcine lymph nodes. The Q marker maintained the greatest twinkling over time compared to all the other markers studied.

Color VISION for improved ultrasound visualization of brachytherapy needles.

BACKGROUND: High dose rate brachytherapy is commonly used in the treatment of prostate cancer. Treatment planning is often performed under transrectal ultrasound (US) guidance, but brachytherapy needles can be challenging to digitize due to the presence of poor US conspicuity and imaging artifacts. The plan accuracy and quality, however, are dependent on the proper visualization of the needles with millimeter accuracy. PURPOSE: This work describes a technique for generating a color overlay of needle locations atop the grayscale US image. Prototype devices were developed to produce vibrations in the brachytherapy needles that generate a high contrast color Doppler (CD) signal that highlights the needle locations with superior contrast and reduced artifacts. Denoted by the acronym color VISION (Vibrationally Induced Shimmering for Identifying an Object's Nature), the technology has the potential to improve applicator conspicuity and facilitate automated applicator digitization. METHODS: Three prototype vibrational devices with frequencies between 200-450 Hz were designed in-house and evaluated with needle implants in a phantom and cadaveric male pelvis using: (1) an actuator attached to the front of a prostate needle template; (2) an actuator attached to the top of the needle template; and (3) a hand-held actuator with a stylet, inserted directly into a needle's inner lumen. Acquired images were postprocessed in MATLAB to evaluate the potential for automated digitization. RESULTS: All prototype devices produced localized shimmering in implanted brachytherapy needles in both the axial and sagittal planes. The template mounted actuators provided better vibrational coupling and ease of operation than the stylet prototype. The Michelson contrast, or visibility, of the shimmering CD signal was 100% compared with ≤40% for B-mode imaging of a single needle. Proof-of-principle for automated applicator digitization using only the CD signal was demonstrated. CONCLUSIONS: The color VISION prototype devices successfully coupled mechanical vibrations into brachytherapy needles to generate US CD shimmering and accurately highlight brachytherapy needle locations. The high contrast and natively registered signal are promising for future work to automate the needle digitization and provide a real-time visual overlay of the applicator on the B-mode US image.

An Ergonomic Risk Assessment of Ophthalmology Residents Using the Rapid Entire Body Assessment (REBA) Scale.

BACKGROUND: The healthcare industry has one of the highest rates of work-related injuries. Ophthalmologists are at particularly high risk for developing musculoskeletal disorders (MSDs), which are often the result of repetitive movements, such as performing slit lamp examinations. Previous studies used the Rapid Entire Body Assessment (REBA) scale to determine the ergonomic risk of a particular task. Higher REBA scores correlate with increased risk of injury, which ranges from negligible risk (1) to very high risk (11+). OBJECTIVE: Given the long-term implications of repetitive examinations by ophthalmologists, this study aims to describe the average ergonomic risk posed to residents using the REBA scale. METHODS: This descriptive case study assessed four ophthalmology residents performing slit lamp examinations between September 2022 and February 2023. Photographs were taken of residents performing slit lamp examinations. Total REBA scores, Score A, Score B, and the REBA scores for each participant were calculated and compared. RESULTS: The average REBA score across all participants was 4.59 (SD±0.89). The highest score was 7.00 and the lowest was 3.00. The average Score A, representing posture for the head, leg, and trunk, was 3.54 (SD±0.74) and the average Score B, representing posture for the upper arm, lower arm, and wrist, was 3.18 (SD±1.22). CONCLUSION: Our study found that residents are at increased risk for developing MSDs. Furthermore, variation in REBA scores between residents indicates that not all residents are at equal ergonomic risk. This highlights an opportunity for ophthalmology residency programs to implement ergonomics training into their curriculum.

Using 3-D-Printed Structures to Evaluate the Potential Causes of the Color Doppler Twinkling Signature.

OBJECTIVE: The color Doppler twinkling artifact has been attributed to existing microbubbles or cavitation occurring on rough objects such as kidney stones, some breast biopsy clips, catheter guidewires and sandpaper. The objective was to investigate the correlation between the surface characteristics of helical constructs with different groove geometries and the occurrence of twinkling, as well as to identify locations conducive to bubble retention and/or cavitation. METHODS: Six half-cylinders were created with a microscale 3-D printer with 5 µm resolution to replicate the geometry of twinkling helical constructs resembling catheter guidewires. Four copies of each marker including a non-twinkling control were printed. The half-cylinders had pitch (peak-to-peak distance) values ranging from 87.5 to 343 µm and amplitude (groove depth) values ranging from 41.5 to 209 µm. The half-cylinders were submerged in degassed water and optically imaged before and after ultrasound insonification to visualize bubbles on the cylinders. The cylinders remained submerged while scanning with the color Doppler mode at frequencies from 3.1 to 6.3 MHz using a GE Logiq E9 scanner and 9L linear array transducer. RESULTS: Two markers exhibited twinkling: one with pitch-to-amplitude ratio of 174/210 µm/µm (0.8) that twinkled only with pre-existing bubbles on the marker; the other had a ratio of 87/87 µm/µm (1.00) that twinkled without pre-existing bubbles on the marker. CONCLUSION: This work provides strong evidence that both existing bubbles and either cavitation or ultrasound wave interactions with patterned or rough surfaces are significant factors in producing the twinkling signature.

Trials, Tribulations, and Techniques for Transitioning to an Extended Deep Plane Facelift for All Patients: Insight from a Very Experienced Surgeon's Perspective.

The extended deep plane facelift is a powerful technique to correct aging of the midface and neck. After many years of superficial muscular aponeurotic system lift techniques, the senior author transitioned to an extended deep plane facelift for all patients. The primary catalyst for this shift in practice was the pursuit of superior rejuvenation of the midface. Consistent uniform elevation of the deep plane with complete ligament release and management of the soft tissue flap were the most significant challenges in the early adoption period. Navigating the transition was facilitated by consultation with experienced colleagues and frequent cadaver dissections. This manuscript details the authors' current technique. Complications and recovery from this technique are similar to those reported with historical techniques and are minimized with proper preparation, precision, and perioperative management. In our experience the results from this procedure are extremely reproducible, durable, and natural, and patients are overwhelmingly extremely satisfied.

Ultrasound Shear Elastography With Expanded Bandwidth (USEWEB): A Novel Method for 2D Shear Phase Velocity Imaging of Soft Tissues.

Ultrasound shear wave elastography (SWE) is a noninvasive approach for evaluating mechanical properties of soft tissues. In SWE either group velocity measured in the time-domain or phase velocity measured in the frequency-domain can be reported. Frequency-domain methods have the advantage over time-domain methods in providing a response for a specific frequency, while time-domain methods average the wave velocity over the entire frequency band. Current frequency-domain approaches struggle to reconstruct SWE images over full frequency bandwidth. This is especially important in the case of viscoelastic tissues, where tissue viscoelasticity is often studied by analyzing the shear wave phase velocity dispersion. For characterizing cancerous lesions, it has been shown that considerable biases can occur with group velocity-based measurements. However, using phase velocities at higher frequencies can provide more accurate evaluations. In this paper, we propose a new method called Ultrasound Shear Elastography with Expanded Bandwidth (USEWEB) used for two-dimensional (2D) shear wave phase velocity imaging. We tested the USEWEB method on data from homogeneous tissue-mimicking liver fibrosis phantoms, custom-made viscoelastic phantom measurements, phantoms with cylindrical inclusions experiments, and in vivo renal transplants scanned with a clinical scanner. We compared results from the USEWEB method with a Local Phase Velocity Imaging (LPVI) approach over a wide frequency range, i.e., up to 200-2000 Hz. Tests carried out revealed that the USEWEB approach provides 2D phase velocity images with a coefficient of variation below 5% over a wider frequency band for smaller processing window size in comparison to LPVI, especially in viscoelastic materials. In addition, USEWEB can produce correct phase velocity images for much higher frequencies, up to 1800 Hz, compared to LPVI, which can be used to characterize viscoelastic materials and elastic inclusions.

Kidney cortex shear wave motion simulations based on segmented biopsy histology.

BACKGROUND AND OBJECTIVE: Biopsy stands as the gold standard for kidney transplant assessment, yet its invasive nature restricts frequent use. Shear wave elastography (SWE) is emerging as a promising alternative for kidney transplant monitoring. A parametric study involving 12 biopsy data sets categorized by standard biopsy scores (3 with normal histology, 3 with interstitial inflammation (i), 3 with interstitial fibrosis (ci), and 3 with tubular atrophy (ct)), was conducted to evaluate the interdependence between microstructural variations triggered by chronic allograft rejection and corresponding alterations in SWE measurements. METHODS: Heterogeneous shear wave motion simulations from segmented kidney cortex sections were performed employing the staggered-grid finite difference (SGFD) method. The SGFD method allows the mechanical properties to be defined on a pixel-basis for shear wave motion simulation. Segmentation techniques enabled the isolation of four histological constituents: glomeruli, tubules, interstitium, and fluid. Baseline ex vivo Kelvin-Voigt mechanical properties for each constituent were drawn from established literature. The parametric evaluation was then performed by altering the baseline values individually. Shear wave velocity dispersion curves were measured with the generalized Stockwell transform in conjunction with slant frequency-wavenumber analysis (GST-SFK) algorithm. By fitting the curve within the 100-400 Hz range to the Kelvin-Voigt model, the rheological parameters, shear elasticity (µ1) and viscosity (µ2), were estimated. A time-to-peak algorithm was used to estimate the group velocity. The resultant in silico models emulated the heterogeneity of kidney cortex within the shear wave speed (SWS) reconstructions. RESULTS: The presence of inflammation showed considerable spatial composition disparities compared to normal cases, featuring a 23 % increase in interstitial area and a 19 % increase in glomerular area. Concomitantly, there was a reduction of 12 % and 47 % in tubular and fluid areas, respectively. Consequently, mechanical changes induced by inflammation predominate in terms of rheological differentiation, evidenced by increased elasticity and viscosity. Mild tubular atrophy showed significant elevation in group velocity and µ1. Conversely, mild and moderate fibrosis exhibited negligible alterations across all parameters, compatible with relatively limited morphological impact. CONCLUSIONS: This proposed model holds promise in enabling patient-specific simulations of the kidney cortex, thus facilitating exploration into how pathologies altering cortical morphology correlates to modifications in SWE-derived rheological measurements. We demonstrated that inflammation caused substantial changes in measured mechanical properties.

Evaluation of Robustness of S-Transform Based Phase Velocity Estimation in Viscoelastic Phantoms and Renal Transplants.

Ultrasound shear wave elastography (SWE) methods are being used to differentiate healthy versus diseased tissue on the basis of their viscoelastic mechanical properties. Tissue viscoelasticity is often studied by analyzing shear wave phase velocity dispersion curves, which is the variation of phase velocity with frequency or wavelength. Recently, a unique approach using a generalized Stockwell transformation (GST-SFK) was proposed for the calculation of dispersion curves in viscoelastic media over expanded frequency band. In this work, the method's robustness was evaluated on data from five custom-made viscoelastic tissue-mimicking phantoms and sixty in vivo renal transplants. For each phantom, 15 shear wave motion data acquisitions were taken, while 10-13 acquisitions were acquired for renal transplants measured in the renal cortex. For each data-set mean and standard deviation (SD) of estimated phase velocity dispersion curves were studied. In addition, the viscoelastic parameters of the Zener model were examined, which were preceded by a convergence analysis. For viscoelastic phantoms scanned with a research ultrasound scanner, and for the in vivo renal transplants scanned with a clinical scanner, the decisive advantage of the GST-SFK method over the standard two-dimensional Fourier transform (2D-FT) method was shown. The GST-SFK method provided dispersion curve estimates with lower SD over a wider frequency band in comparison to the 2D-FT method. These advantages are relevant to the analysis of the mechanical properties of tissues in clinical practice to discriminate healthy from diseased tissue.

Infratemporal Fossa Abscess Drainage via a Trans-Oral Image Guided Approach.

Deep neck space infections can cause antibiotic-resistant abscesses that can impinge on vital anatomical structures. Image-guided surgery systems using preoperative computed tomography (CT) imaging can be utilized to characterize pathology and assist surgeons in avoiding iatrogenic injury. This manuscript explores the presentation and unique CT-guided surgical management of an infratemporal fossa abscess in a 48-year-old male who presented with left-sided dental pain and facial swelling that had progressed despite antibiotics and dental extraction. CT-guided imaging can assist in localizing and protecting vital anatomical structures during deep neck abscess drainage and can prevent the potential risks and complications of classic surgical approaches.

A new way to visualize prostate brachytherapy needles using ultrasound color Doppler and needle surface modifications.

PURPOSE: Suboptimal ultrasound conspicuity of the brachytherapy applicator can lead to inaccurate image reconstructions of the applicator resulting in decreased tumor control or increased normal tissue dose. This feasibility study aims to improve ultrasound conspicuity of high-dose rate (HDR) brachytherapy needles by modifying the surface of the needles to produce a color Doppler twinkling signature. MATERIALS AND METHODS: Surface modifications of standard 17-gauge titanium HDR brachytherapy needles included laser-scribing, application of polymethyl methacrylate (PMMA), and coating with a commercially available echogenic coating. Laser-scribing was performed with variable widths (0.1-1 mm) and depths (10-100 µm). The echogenic coating was applied with 3 different thicknesses (27, 40, and 64 µm). Unmodified and modified needles were imaged under B-mode and color Doppler ultrasound in phantom and cadaver, and the signal strength was recorded. RESULTS: Laser-scribed, PMMA-coated, and echogenic-coated brachytherapy needles produced a twinkling signature along the needle shaft on color Doppler ultrasound. Twinkling was observed with laser-scribe depths >20 µm and widths >0.1 mm and from echogenic coatings 40 µm and 64 µm thick. Twinkling was not observed with unmodified needles. The twinkling signature had a spectral composition with a uniform magnitude between the velocities of 2 to 16 cm/s. CONCLUSIONS: Color Doppler ultrasound of surface-modified brachytherapy applicators may improve applicator conspicuity aiding applicator placement and digitization. HDR brachytherapy needles may be modified to produce the twinkling signature via laser-scribing, PMMA rings, or applying an echogenic coating.

Comb Detection for Measuring Shear Wave Propagation.

Plane wave compounding (PWC) is widely used to measure the propagation of shear waves. Implementing PWC on most commercial ultrasound scanners is challenging because all channel (>128) data must be processed or transferred to the host computing unit in real time. Comb detection transmits multiple focused beams simultaneously and results in a reduced number of receive lines to be processed in parallel. These comb beams are scanned laterally to acquire receive lines at different lateral positions in order to obtain data over a large region of interest (ROI). One of the potential issues with using multiple simultaneously transmitted beams is the issue of crosstalk between the beams. Crosstalk is analyzed through simulated beam patterns, simulated B-mode images, and motion data from shear wave elastography (SWE) experiments. Using a Hamming window on transmit and receive can suppress crosstalk to 1.2% root-mean-square error (RMSE, normalized RMSE to the peak magnitude of the reference signal) for shear wave motion signals. Four comb beams with three laterally scanned locations cover almost the entire field of view (FOV) and achieve the same frame rate as PWC with three angles. Phantom and in vivo studies demonstrate comparable motion data of comb detection to PWC in terms of motion signal quality and measured phase velocity. In addition, comb detection provides motion with lower noise and stronger signals than PWC, which is believed to be due to the advantages of transmitting focused beams rather than plane waves (PWs).

Inpatient Otolaryngology Consultations and COVID-19: The Surge and Lasting Effects at an Urban, Academic Institution.

Objective: This study aims to examine the lasting effects of the coronavirus disease 2019 (COVID-19) pandemic on inpatient otolaryngology consultations. Methods: In a retrospective analysis, inpatient otolaryngology consultations at an urban, academic tertiary care center were reviewed over the course of 2 years (Jun 2019-Jun 2021). The consultations were categorized by time period based on the local data for COVID-19 hospitalizations and deaths as follows: pre-COVID (Jun 2019-Feb 2020), Surge 1 (Mar 2020-May 2020), Surge 2 (Oct 2020-Jan 2021), and Post Surge (Mar 2021-Jun 2021). Results: A total of 897 patients undergoing an inpatient otolaryngology consultation across all 4 time periods were included for analysis. The average consultations per day was 1.67 ± 0.24 in pre-COVID times, and dropped acutely to 0.86 ± 0.33 consultations per day during Surge 1. The consultation volume was not statistically different from pre-COVID levels during Surge 2 (1.33 ± 0.35) and Post Surge (1.60 ± 0.20). Reason for consultation and procedures performed did not vary significantly between pre-COVID times and Post Surge, except that consultation for postoperative complaint was less frequent in Post Surge (4.8% vs 1.0%, P = .02). More patients had been screened with rapid antigen COVID testing in Post Surge versus Surge 1 (20.1% vs 7.6%, P = .04). Conclusions: Inpatient otolaryngology consultation volumes, indications, and procedures performed at an urban, academic institution returned to pre-COVID levels after being significantly impacted during Surge 1.

Using US Twinkling Artifact to Identify Breast Biopsy Markers: Brief Report.

Breast biopsy markers play an essential role in the surgical management of patients with clinically node-positive breast cancer. Marking a pathology-proven lymph node ensures accurate imaging assessment of response to neoadjuvant systemic therapy and decreased false-negative rates in sentinel lymph node biopsy. There is a clinically unmet need to make breast biopsy markers, particularly in the axilla, more sonographically visible or identifiable for preoperative localization purposes. Previously described color Doppler US twinkling artifact of some breast biopsy markers in in vitro gel phantoms and in ex vivo cadaveric breasts suggests that twinkling of such markers can be leveraged for improved in vivo detection. In this retrospective case series of eight female patients (mean age, 58.6 years ± 12.3 [SD]), conventional B-mode US imaging failed to identify the biopsy marker associated with a surgical target in the breast or in an axillary lymph node. However, in each patient, the marker was successfully identified with the help of color Doppler US twinkling. Keywords: Breast, Ultrasound, Color Doppler US, Lymphatic, Artifacts, Biopsy Marker Published under a CC BY 4.0 license.

Improving Visualization of Osteochondritis Dissecans Using Delay-Multiply-and-Sum Reconstruction.

OBJECTIVE: Osteochondritis dissecans (OCD) of the capitellum is a joint defect that is common among adolescent athletes. It is important to diagnose OCD as early as possible, because early-stage OCD lesions have a high rate of spontaneous healing with rest. Medical ultrasound could potentially be used as a screening tool for OCD but is limited by the use of delay-and-sum (DAS) reconstruction. In this study, we tested conventional delay-multiply-and-sum (DMAS) and novel low-pass DMAS reconstruction algorithms for better visualization of OCD lesions. METHODS: We created phantom and cadaveric OCD models that simulated a range of OCD lesion severities and stabilities. We also imaged an in vivo case of OCD in a patient study. In the reconstructed images, several profiles were taken to measure OCD lesion contrast, cartilage contrast, crack thickness error and bone interface clarity. RESULTS: In the phantom and cadaveric OCD models, we found that histogram-matched conventional DMAS reconstruction improved lesion contrast by up to 16%, cartilage contrast by 26% and bone interface clarity by 15% on average compared with DAS reconstruction. Histogram-matched low-pass DMAS reconstruction improved lesion contrast by up to 22%, cartilage contrast by 45%, and bone interface clarity by 29% on average compared with DAS reconstruction. In the in vivo case of OCD, we found that histogram-matched conventional and low-pass DMAS reconstruction improved lesion contrast by 22% and 26%, respectively. CONCLUSION: The application of DMAS reconstruction improved the ability of medical ultrasound to detect OCD lesions of the capitellum when compared with DAS reconstruction.

Successful Reimplantation of Extruded Lead after Hypoglossal Nerve Stimulation Surgery.

Infection and extrusion of hardware are known complications of hypoglossal nerve stimulation surgery. We present a unique case of an extruded hardware lead successfully managed with reimplantation without need for explantation and new device placement. The topic will be discussed in context of the body of literature related to extruded medical device management. Laryngoscope, 133:2821-2822, 2023.

Evaluating Variability of Commercial Liver Fibrosis Elastography Phantoms.

OBJECTIVE: Liver fibrosis has been found to increase the mechanical stiffness of the liver. To mimic different stages of liver fibrosis, commercially available phantoms (Model 039, CIRS, Inc.) have been produced for clinical quality assurance and research purposes. The purpose of this study was to investigate the mechanical property variability of the phantoms in two lots of CIRS Model 039 phantoms. METHODS: Each lot consisted of phantoms of four stiffness types, and there were 8-10 phantoms of each type. Shear wave elastography measurements were conducted on each phantom at 10 different angles. Group velocity measurements and phase velocity curves were calculated for every SWE acquisition. Multilevel functional principal component analysis (MFPCA) was performed on phase velocity data, which decomposes each phase velocity curve into the sum of eigenfunctions of two levels. The variance of the component scores of levels 1 and 2 were used to represent inter-phantom and intra-phantom variability, respectively. The 95% confidence intervals of phase velocity in a phantom type were calculated to reflect curve variability. DISCUSSION: The standard deviations of the group velocity for phantoms of any type were less than 0.04 and 0.02 m/s for lots 1 and 2, respectively. For both lots, in every type, the phase velocity curves of most individual phantoms fall within the 95% confidence interval. CONCLUSION: MFPCA is an effective tool for analyzing the inter- and intra-phantom variability of phase velocity curves. Given the known variability of a fully tested lot, estimation of the variability of a new lot can be performed with a reduced number of phantoms tested.

Improving ultrasound-based brachytherapy needle conspicuity by applying an echogenic coating.

BACKGROUND: Applicator conspicuity in ultrasound-guided brachytherapy procedures is commonly impaired by imaging artifacts or non-ideal imaging geometry, which can slow down applicator position digitization and increase the geometric uncertainty of the delivered dose distribution. PURPOSE: The purpose of this study was to improve the conspicuity of high-dose rate (HDR) brachytherapy needles under B-mode ultrasound imaging by applying an echogenic surface coating. Our hypothesis was that an echogenic coating would reduce artifacts and improve needle visualization within regions of signal degradation. METHODS: In this study, 17-gauge, 25-cm long titanium HDR brachytherapy needles were coated with acoustically reflective microspheres over a 2.5 cm region starting from the needle tip. Three coating thicknesses (27 µm, 40 µm, 64 µm) were compared against an uncoated control needle. The coated and uncoated needles were imaged using B-mode ultrasound in a tissue-equivalent prostate phantom and in a cadaverous male pelvis using a transrectal probe. Needle conspicuity was assessed under multiple conditions: a single needle implant, an implant with multiple needles between the probe and the needle of interest, and an angled needle implant. All images were assessed qualitatively for needle conspicuity and the presence of artifacts and quantitatively using grey-scale image intensity values. RESULTS: The 64 µm echogenic coating reduced the magnitude of reverberation artifacts by 31 ± 14% and comet tail artifacts by 40%-70%. The echogenic coating also improved needle contrast, measured by the relative differences in signal intensity compared with the adjacent environment, when needles were angled up to 30° with respect to the transducer probe in the cadaver. The improvements in conspicuity and artifact reduction increased with increasing coating thickness. The performance of the needles coated with the 64 µm thickness was qualitatively superior and yielded high-contrast, well-circumscribed signals in the cadaverous male pelvis, even under situations where a needle was acoustically shadowed by multiple other needles. CONCLUSIONS: An echogenic surface coating reduced imaging artifacts and improved needle conspicuity under realistic clinical conditions for ultrasound-based prostate or gynecological brachytherapy. The improved conspicuity has the potential to improve the efficiency of needle placement and the accuracy of needle position digitization during brachytherapy procedures.

Factors Associated With Ultrasound Color Doppler Twinkling by Breast Biopsy Markers: In Vitro and Ex Vivo Evaluation of 35 Commercially Available Markers.

BACKGROUND. Targeted axillary lymph node dissection after neoadjuvant systemic therapy (NST) for breast cancer depends on identifying marked metastatic lymph nodes. However, ultrasound visualization of biopsy markers is challenging. OBJECTIVE. The purpose of our study was to identify biopsy markers that show actionable twinkling in cadaveric breast and to assess the association of actionable twinkling with markers' surface roughness. METHODS. Commercial breast biopsy markers were evaluated for twinkling artifact in various experimental conditions relating to scanning medium (solid gel phantom, ultrasound coupling gel, cadaveric breast), transducer (ML6-15, 9L, C1-6), and embedding material (present vs absent). Markers were assigned twinkling scores from 0 (confident in no twinkling) to 4 (confident in exuberant twinkling); a score of 3 or greater represented actionable twinkling (sufficient confidence to rely solely on twinkling for target localization). Markers were hierarchically advanced to evaluation with increasingly complex media if showing at least minimal twinkling for a given medium. A 3D coherence optical profiler measured marker surface roughness. Mixed-effects proportional odds regression models assessed associations between twinkling scores and transducer and embedding material; Wilcoxon rank sum test evaluated associations between actionable twinkling and surface roughness. RESULTS. Thirty-five markers (21 with embedding material) were evaluated. Ten markers without embedding material advanced to evaluation in cadaveric breast. Higher twinkling scores were associated with presence of embedding material (odds ratio [OR] = 5.05 in solid gel phantom, 9.84 in coupling gel) and transducer (using the C1-6 transducer as reference; 9L transducer: OR = 0.36, 0.83, and 0.04 in solid gel phantom, ultrasound coupling gel, and cadaveric breast; ML6-15 transducer: OR = 0.07, 0.18, and 0.00 respectively; post hoc p between 9L and ML6-15: p < .001, p = .02, and p = .04). In cadaveric breast, three markers (Cork, Professional Q, MRI [Flex]) exhibited actionable twinkling for two or more transducers; surface roughness was significantly higher for markers with than without actionable twinkling for C1-6 (median values: 0.97 vs 0.35, p = .02) and 9L (1.75 vs 0.36; p = .002) transducers. CONCLUSION. Certain breast biopsy markers exhibited actionable twinkling in cadaveric breast. Twinkling was observed with greater confidence for the C1-6 and 9L transducers than the ML6-15 transducer. Actionable twinkling was associated with higher marker surface roughness. CLINICAL IMPACT. Use of twinkling for marker detection could impact preoperative or intraoperative localization after NST.

Acoustic Force Elastography Microscopy.

OBJECTIVE: Hydrogel scaffolds have attracted attention to develop cellular therapy and tissue engineering platforms for regenerative medicine applications. Among factors, local mechanical properties of scaffolds drive the functionalities of cell niche. Dynamic mechanical analysis (DMA), the standard method to characterize mechanical properties of hydrogels, restricts development in tissue engineering because the measurement provides a single elasticity value for the sample, requires direct contact, and represents a destructive evaluation preventing longitudinal studies on the same sample. We propose a novel technique, acoustic force elastography microscopy (AFEM), to evaluate elastic properties of tissue engineering scaffolds. RESULTS: AFEM can resolve localized and two-dimensional (2D) elastic properties of both transparent and opaque materials with advantages of being non-contact and non-destructive. Gelatin hydrogels, neat synthetic oligo[poly(ethylene glycol)fumarate] (OPF) scaffolds, OPF hydroxyapatite nanocomposite scaffolds and ex vivo biological tissue were examined with AFEM to evaluate the elastic modulus. These measurements of Young's modulus range from approximately 2 kPa to over 100 kPa were evaluated and are in good agreement with finite element simulations, surface wave measurements, and DMA tests. CONCLUSION: The AFEM can resolve localized and 2D elastic properties of hydrogels, scaffolds and thin biological tissues. These materials can either be transparent or non-transparent and their evaluation can be done in a non-contact and non-destructive manner, thereby facilitating longitudinal evaluation. SIGNIFICANCE: AFEM is a promising technique to quantify elastic properties of scaffolds for tissue engineering and will be applied to provide new insights for exploring elastic changes of cell-laden scaffolds for tissue engineering and material science.